Tag Archives: 2008-2013
For BMW X5 E70 2008-2013 Right Hand Drive Plastic Carbon Fiber Accessories
Please Kindly check our item description and photos, confirm it with your car. If the surface of the installation location has wax oil, Must First Clean it up before install. Otherwise, can not install well. Recommend go to professional automotive neauty shops install. Adhesive tape is at the back. Please note that please use the heat gun to warm up the adhesive tape before installed, to make the item stick tightly. (No need too hot). Pasticl carbon fiber style. Notice: Cause the same car model may be differently produced in different country. Condition:100% Brand New and Good Quality Material. Color: Carbon Fiber Color. Not real carbon fiber. (As the picture show).
Front & Rear Brake Rotors + Ceramic Pads for 2008-2011 BMW 323i 2008-2013 328i
BMW 323i 2008 2009 2010 2011, BMW 328i 2008 2009 2010 2011 – Coupe Sedan, BMW 328i 2012 2013 – 3.0 L6 Engine Std Brakes Coupe. 2008, 2009, 2010, 2011. 3.0 L6 Engine, Std Brakes, Coupe. For your new braking system to operate at its performance capacity, it is important to’break-in’ the rotors and brake pads. This procedure is called bedding and it is encouraged you follow the steps below upon completion of the installation. Find a safe and open area where you will be able to accelerate and stop safely multiple times. Accelerate to 35mph (55km/h) and aggressively stop to 5mph (8km/h) in rapid successions without letting the brakes cool down and without stopping. Repeat this six times. Accelerate to 35mph (55km/h) and this time, moderately stop to 5mph (8km/h) in rapid successions without letting the brakes cool down and without stopping. Drive around for approximately 6-8 minutes at a moderate speed without excessively using the brakes or coming to a complete stop. For Elite XDS & Geomet OE (our coated rotors), and 3 extra minutes. Once this is complete, stop the vehicle and allow the brakes to cool down. This should take about 40 minutes or so. This concludes the bedding procedure and you can now use your brakes normally. However, certain restrictions apply. Note on UPS Extended Area Surcharge: This surcharge is levied by UPS, not Max Advanced Brakes. CT, DE, DC, IL, IN, KY, ME, MD, MA, MI, NH, NJ, NY, NC, OH, PA, RI, SC, TN, VT, VA, WV. AL, AZ, AR, CO, FL, GA, IA, KS, LA, MN, MS, MO, NE, SD, WI. CA, ID, MT, NV, NM, ND, OK, OR, TX, UT, WA, WY. Processing time is subject to change depending on holiday schedule & volume of orders.
Carbon Fiber HighKick Rear Trunk Spoiler For INFINITI G37 Q60 Coupe 2008-2013
Easy Installation? Install with adhesive tape, which is included in package & No need to drill. UV-Resistant Coating? Baking paint surface high temperature UV layer treatment, not afraid of exposure to the sun cracking and paint off, fading. High Precision? Comes with pre-cut holes for rear view camera. Install Note: – If your car have factory spoiler, you need to remove it and then inatall ours. This spoiler will cover holes left By factory spoiler. In winter or in areas with low temperature, please use hot air blower to preheat the double-sided adhesive tape fully before installation, otherwise the adhesive tape has no adhesion. After sticking the spoiler, it is strongly recommended to fix the two ends and the middle of the tail with large transparent tape, and do not wash the car or rain for 3-5 hours, so as to achieve better long-term fixation effect. We provide clear pictures, measurements where possible. Please check as much as possible to make sure the item is the one that you need. Please allow 0.5-1 inch difference due to manual measurement. Installation Instructions is not included. Professional Installation Is Highly Recommended!