Next page →
6 Running Boards for 2020-2024 Jeep Gladiator JT 4 Door Drop Down Side Steps
6inch side steps feature two-stair layout to provide better convenience for vehicles with lift kits and oversized wheel tires. Also allows for easier rooftop operation. Three-tube design provides more protection for the bottom and the side of the car, also preventing from getting stuck on the rocker plate or hanging obstacles. Welded brackets provide additional strength. Package contains 2 nerf bars, set of brackets & hardware; Installation can be completed within 20 minutes with no cutting or drilling. Unique powder coating offers exceptional rust and corrosion resistance so you can drive under any condition. The laser cutting step plate achieves a non-slipping step surface and reinforced grip. Proven to handle up to 550 lbs. No-hassle Service and Note. The bracket is not pre-welded on the step bars! Please confirm the cab picture in the listing before ordering. For your safety, professional installation recommended.
Front & Rear Drilled Brake Rotors + Pads for 2015-2020 Chevy Colorado GMC
Chevrolet Colorado 2015 2016 2017 2018 2019 2020, GMC Canyon 2015 2016 2017 2018 2019 2020. 2015, 2016, 2017, 2018, 2019, 2020. For your new braking system to operate at its performance capacity, it is important to’break-in’ the rotors and brake pads. This procedure is called bedding and it is encouraged you follow the steps below upon completion of the installation. Find a safe and open area where you will be able to accelerate and stop safely multiple times. Accelerate to 35mph (55km/h) and aggressively stop to 5mph (8km/h) in rapid successions without letting the brakes cool down and without stopping. Repeat this six times. Accelerate to 35mph (55km/h) and this time, moderately stop to 5mph (8km/h) in rapid successions without letting the brakes cool down and without stopping. Drive around for approximately 6-8 minutes at a moderate speed without excessively using the brakes or coming to a complete stop. Once this is complete, stop the vehicle and allow the brakes to cool down. This should take about 40 minutes or so. This concludes the bedding procedure and you can now use your brakes normally. However, certain restrictions apply. Note on UPS Extended Area Surcharge: This surcharge is levied by UPS. CT, DE, DC, IL, IN, KY, ME, MD, MA, MI, NH, NJ, NY, NC, OH, PA, RI, SC, TN, VT, VA, WV. AL, AZ, AR, CO, FL, GA, IA, KS, LA, MN, MS, MO, NE, SD, WI. CA, ID, MT, NV, NM, ND, OK, OR, TX, UT, WA, WY. Processing time is subject to change depending on holiday schedule & volume of orders.
Front & Rear Drilled Brake Rotors + Pads for 2007-2015 2016 2017 2018 BMW X5
BMW X5 2007 – 3.0si – 3.0si, BMW X5 2008 – 3.0si – 3.0si, BMW X5 2009 – xDrive30i – xDrive30i, BMW X5 2010 – xDrive30i – xDrive30i, BMW X5 2011 – xDrive35i – xDrive35i, BMW X5 2012 – xDrive35i – xDrive35i, BMW X5 2013 – xDrive35i – xDrive35i, BMW X5 2014 – sDrive35i – sDrive35i – xDrive35d – xDrive35d – xDrive35i – xDrive35i, BMW X5 2015 – sDrive35i – sDrive35i – xDrive35d – xDrive35d – xDrive35i – xDrive35i, BMW X5 2016 – sDrive35i – sDrive35i – xDrive35d – xDrive35d – xDrive35i – xDrive35i, BMW X5 2017 – sDrive35i – sDrive35i – xDrive35d – xDrive35d – xDrive35i – xDrive35i, BMW X5 2018 – sDrive35i – sDrive35i – xDrive35d – xDrive35d – xDrive35i – xDrive35i. 3.0si – 3.0si. XDrive30i – xDrive30i. XDrive35i – xDrive35i. SDrive35i – sDrive35i – xDrive35d – xDrive35d – xDrive35i – xDrive35i. For your new braking system to operate at its performance capacity, it is important to’break-in’ the rotors and brake pads. This procedure is called bedding and it is encouraged you follow the steps below upon completion of the installation. Find a safe and open area where you will be able to accelerate and stop safely multiple times. Accelerate to 35mph (55km/h) and aggressively stop to 5mph (8km/h) in rapid successions without letting the brakes cool down and without stopping. Repeat this six times. Accelerate to 35mph (55km/h) and this time, moderately stop to 5mph (8km/h) in rapid successions without letting the brakes cool down and without stopping. Drive around for approximately 6-8 minutes at a moderate speed without excessively using the brakes or coming to a complete stop. For Elite XDS & Geomet OE (our coated rotors), and 3 extra minutes. Once this is complete, stop the vehicle and allow the brakes to cool down. This should take about 40 minutes or so. This concludes the bedding procedure and you can now use your brakes normally. However, certain restrictions apply. Note on UPS Extended Area Surcharge: This surcharge is levied by UPS, not Max Advanced Brakes. CT, DE, DC, IL, IN, KY, ME, MD, MA, MI, NH, NJ, NY, NC, OH, PA, RI, SC, TN, VT, VA, WV. AL, AZ, AR, CO, FL, GA, IA, KS, LA, MN, MS, MO, NE, SD, WI. CA, ID, MT, NV, NM, ND, OK, OR, TX, UT, WA, WY. Processing time is subject to change depending on holiday schedule & volume of orders.
Zwilling PRO 38408-140 5.5 in SANTOKU Knife, Made in GERMANY, Carbon Steel, NEW
Zwilling PRO 38401-200 5.5-inch SANTOKU Knife w/ Curved Bolster & Full-Edge Utility. Blade Material: Special Stain Resistant Formula Carbon Steel, FRIODUR Ice Hardened. Manufactured: Made in GERMANY. Condition: NEW, Never Used! Need a Knife Block to go along with your new Knife? I have all sizes, brands, and finishes available! Check out my store OneOfAKindCustomCollectibles.
Bumper Face Bar Retainer Bracket Brace Mounting Kit Front BCYE34880 for CX-30 3
Bumper Face Bar Retainer Bracket Brace Mounting Kit Front BCYE34880 for CX-30 3. Manufactured from top quality components, this is your best option and inexpensive replacement for your rebuild, repair, and maintenance needs – an OE replacement product for your damaged or aged factory part. Replacement – the most affordable brand name for replacement parts that you need! Replacement is a professional brand for autobody, lighting parts, electrical, brake, suspension, intake and exhaust, and cooling and heating products. Brand New in the Box – Fit and Quality Guaranteed! WARNING: This product can expose you to chemical which is known to the State of California to cause cancer and birth defects or other reproductive harm. Compatible with the following vehicles. 2021 3 100th Anniversary Edition. 2020 CX-30 (submodel: Base, Preferred, Premium, Select).
APR Carbon Fiber 2.0/1.8 TSI Intake System CI100035
The APR Carbon Fiber Intake System lets your engine breath! The stunning carbon fiber design rejects power-robbing heat from the engine bay and delivers an unrestrictive path for cold, dense air fed from outside of the engine bay. The system dramatically outflows the stock intake, sharpening throttle response and lessening strain on the turbocharger, all while supporting over 500 horsepower! The system installs in minutes, looks fantastic, delivers a sporty engine note, and is recommended at all stages of performance. The APR Carbon Fiber Intake System connects to the factory turbo inlet piping, and provides substantial gains. Those looking to complete the system can opt for the optional APR Carbon Fiber Turbo Inlet pipe. The turbo inlet pipe is a continuous 80mm pipe that connects to the turbocharger via a port-matching silicon coupler. The PCV system conveniently connects to the intake via a billet aluminum adapter. Lastly, the system uses a flex coupler that allows adequate engine movement and flex. Increased Horsepower and Torque. Flattened Torque Curve (engine is less’peaky’). Enhanced Engine Volumetric Efficiency. Enhanced Sound of Turbo Diverter Valve. Installs in an Hour (does not require bumper or headlight removal). Maintains Clean Appearance by Retaining Factory Engine Cover. Maintains All Factory Emissions Components. Fits Both Manual and Automatic Transmissions. Unique Thermal Barrier Composite Construction Ensures Low Inlet Temperatures. Fully Compatible and Complimentary with APR Software and Exhaust systems. The APR Intake system dramatically out performs the factory intake system and improves upon the previous design. As performance increases, so does the importance of a high-flow high-quality intake system as a large pressure drop forms between the factory intake’s inlet and outlet. As listed in the chart, the APR Intake system flowed dramatically more than the stock unit. This trend continues to climb as performance levels increase. The APR Intake System is roughly 50% less restrictive compared to the factory intake at stage 2 power levels, and is off the charts at K04 and Stage 3 power levels. By allowing the engine to breathe, the intake system reduces stress placed on the turbocharger, lowers the intake air temperature, and allows for performance gains upwards of 15 HP with the stock turbo. As performance climbs further using larger turbochargers, so does the power gain seen with the APR Intake system!
Running Boards For 2020-2024 Jeep Gladiator JT 4 Door with 3 Drop Steps Nerf Bar
Heavy Duty Carbon Steel+Steps Dual-Stage Textured Black Powder. Color: Black 100% Brand New Steps 2 Pcs Side steps(1 pcs for driver side and 1 pcs for passenger side) All mounting hardware and Installation instruction included. Drop Down Running Boards. The sleek drop-off style allows you to easily hop in and out of your truck while enhancing its contours. Wheel to Wheel Truck Step Stretches From the Back of the Front Fender to the Front of the Rear Fender, Which Is Longer Than Normal. Long Enough to Entry Into the Truck Easily as Well as the Bed. Perfect for People Who Often Load and Unload Goods Without Having to Climb Deep Into the Back of the Truck. The Drop step makes it easier for the elderly and children to get in and out of the car. The side steps designed with leakage holes can effectively prevent water accumulation and sediment accumulation in the steps. EASY TO INSTALL – Easy bolt-on installation. No drilling or cutting required. Anti-skid, durable and rust free It has the technology that ensures safety and the product’s stability after installation. Thank you for your understanding. If the item is defective, please notify us within 3 days after receipt of the item. The item is not refundable after 30 days, it will not be repaired. We try our best to make our buyers satisfy. Let’s solve the problem together! May all goes well with you, my dearest friends! So your positive FEED BACK is very important. Here is an illustration showing how to leave the positive FEED BACK. Please follow the following step. Thank you so much. And welcome back to our store again. C h e v y. T a c o m a. D o d g e. J e e p. N i s s a n.
Motiontop DRY CARBON FIBER INTAKE AIR SCOOP SET BMW F90 M5
Boost the performance of your F90 M5 with Motiontop’s Dry Carbon Intake Air Scoop Set-an innovative upgrade designed to redefine your driving experience. Strategically positioned behind the front grills, these air ducts are engineered to deliver a powerful “ram-air” effect. By harnessing the natural motion of air intake, they enhance static air pressure entering the manifold, optimizing engine performance. Experience a cooler engine and improved airflow as these ducts channel increased cooler air, ensuring optimal efficiency and power. The lightweight and visually striking features of carbon fiber not only enhance performance but also elevate the aesthetic appeal of your car’s front end. Crafted from premium dry carbon fiber, our intake air ducts undergo a meticulous manufacturing process. The “pre-preg” method, incorporating impregnated carbon materials and autoclave vacuuming, results in a lightweight, durable, and precisely formed carbon piece. This process minimizes waste, delivering a flawless finish with minimal imperfections. Motiontop’s Dry Carbon Intake Air Scoop Set is the perfect addition to any intake system, promising enhanced overall performance. Invest in cutting-edge technology and a sleek design that not only boosts power but also adds a touch of sophistication to your vehicle’s front end. Upgrade your driving experience with Motiontop’s commitment to excellence.
Next page →