Buick LaCrosse 2012 2013 2014 2015 2016 – Solid Rear Rotor, Buick Regal 2011 – 2.4 L4 Engine, Buick Regal 2012 2013 2014 2015 2016 – 296mm (11.65) Diameter Front Rotor, Chevrolet Malibu Limited 2016 – 296mm (11.65) Diameter Front Rotor, Chevrolet Malibu 2013 2014 2015 – 296mm (11.65) Diameter Front Rotor. 2012, 2013, 2014, 2015, 2016. Solid Rear Rotor. 2.4 L4 Engine. 296mm (11.65) Diameter Front Rotor. For your new braking system to operate at its performance capacity, it is important to’break-in’ the rotors and brake pads. This procedure is called bedding and it is encouraged you follow the steps below upon completion of the installation. Find a safe and open area where you will be able to accelerate and stop safely multiple times. Accelerate to 35mph (55km/h) and aggressively stop to 5mph (8km/h) in rapid successions without letting the brakes cool down and without stopping. Repeat this six times. Accelerate to 35mph (55km/h) and this time, moderately stop to 5mph (8km/h) in rapid successions without letting the brakes cool down and without stopping. Drive around for approximately 6-8 minutes at a moderate speed without excessively using the brakes or coming to a complete stop. Once this is complete, stop the vehicle and allow the brakes to cool down. This should take about 40 minutes or so. This concludes the bedding procedure and you can now use your brakes normally. However, certain restrictions apply. Note on UPS Extended Area Surcharge: This surcharge is levied by UPS. CT, DE, DC, IL, IN, KY, ME, MD, MA, MI, NH, NJ, NY, NC, OH, PA, RI, SC, TN, VT, VA, WV. AL, AZ, AR, CO, FL, GA, IA, KS, LA, MN, MS, MO, NE, SD, WI. CA, ID, MT, NV, NM, ND, OK, OR, TX, UT, WA, WY. Processing time is subject to change depending on holiday schedule & volume of orders.
Hyundai Elantra 2017 2018 2019 2020 – Exc 1.6 L4 Engine. 2017, 2018, 2019, 2020. Exc 1.6 L4 Engine. For your new braking system to operate at its performance capacity, it is important to’break-in’ the rotors and brake pads. This procedure is called bedding and it is encouraged you follow the steps below upon completion of the installation. Find a safe and open area where you will be able to accelerate and stop safely multiple times. Accelerate to 35mph (55km/h) and aggressively stop to 5mph (8km/h) in rapid successions without letting the brakes cool down and without stopping. Repeat this six times. Accelerate to 35mph (55km/h) and this time, moderately stop to 5mph (8km/h) in rapid successions without letting the brakes cool down and without stopping. Drive around for approximately 6-8 minutes at a moderate speed without excessively using the brakes or coming to a complete stop. For Elite XDS & Geomet OE (our coated rotors), and 3 extra minutes. Once this is complete, stop the vehicle and allow the brakes to cool down. This should take about 40 minutes or so. This concludes the bedding procedure and you can now use your brakes normally. However, certain restrictions apply. Note on UPS Extended Area Surcharge: This surcharge is levied by UPS, not Max Advanced Brakes. CT, DE, DC, IL, IN, KY, ME, MD, MA, MI, NH, NJ, NY, NC, OH, PA, RI, SC, TN, VT, VA, WV. AL, AZ, AR, CO, FL, GA, IA, KS, LA, MN, MS, MO, NE, SD, WI. CA, ID, MT, NV, NM, ND, OK, OR, TX, UT, WA, WY. Processing time is subject to change depending on holiday schedule & volume of orders.